Logotipo Texsa, S.A.

TEXPRIMER

TEXPRIMER is an epoxy-water based two component primer. It is low-viscosity and odourless and, due to its high technology, catalyses with modified amines, inducing greater adhesion power on the support and achieving the optimal state of adherence.

Technical documentation

  • Logo Facebook
  • Logo Twitter
  • Logo Linkedin
  • Advantages
  • Application
  • Installation
  • Storage
  • Regulations
. Easy application (brush, roller or airless equipment)
. Excellent adherence, even on concrete supports with residual moisture
. Dissolves in water, environmentally-friendly
. Odourless
. Excellent adherence on non-absorbent surfaces
Primer for liquid polyurethane waterproofing systems.
Bonding interphase between liquid polyurethane membranes, if time has been exceeded for bonding of the same. Primer on concrete supports that have residual moisture.
In non-absorbent substrates such as steel, aluminium, ceramic tile, etc.
As a sealant for pores, cracks and capillarities in the concrete.
· SUPPORT PREPARATION:
- Carefully preparing the surface is essential for good durability.
- The surface must be clean, flat, and free of contaminants, which could negatively affect adhesion of the membrane. Humidity must not exceed 8%. Substrate compression resistance must be ≥25 MPa, and the adhesive resistance ≥1.5 MPa. Loose layers, dirt, grease, oils, organic substances and dust must be removed.
· MIXTURE:
- Apply TEXPRIMER B into TEXPRIMER A and gently mix for 3-5 minutes with a mechanical mixer. Mixture ratio 3:1 (A:B).
- Then, dilute with 15-25% clean water.
Installation :
Add 5 to 10 % of water to component A and make it uniform. Immediately after pour component B and
continue to mix for between 3 and 5 minutes, until the red-coloured mixture is uniform.
Mixture ratio : 3:1.
Apply with a brush, roller or airless equipment.
Each layer requires 12 hours to dry.
While the primer is still tacky, apply the polyurethane liquid membrane.
The fresh concrete structures should be left to cure for 28 days minimum.
In very porous surfaces, apply 2 layers of the product. If the concrete layer has residual moisture, apply 2 layers of the TEXPRIMER and in the last fresh layer apply 0.5 kg/m2 of special aggregate. If for some reason it is left to dry for more than 24 hours, it is recommended to sand the surface and apply a new layer of primer.
It is recommended to install some sort of mechanical ventilation in closed and humid areas in order to accelerate the drying of the support.
Coverage :
100 g/m2 - 200 g/m2 in one of two layers.
Factors such as porosity of the surface, temperature and the method of application can alter the coverage amount.
This amount of coverage is based on application using a roller on a surface in optimal conditions
APPLICATION CONDITIONS:
Temperature: +10 ºC and 35 ºC
REACTION TIMES:
Mixture duration: ± 45 min
Can be walked on/apply second coat: ± 6-12 hours
Curing time: ± 7 days
TEXPRIMER is supplied in sets of 2 components:
Components: A 15 kg, B 5 Kg (large set)
Components: A 3 kg, B 1 Kg (small set).
Storage :
Must be kept in a dry place and protected from humidity and the sun.
Maximum recommended storage time: 12 months at 25º C in its own packaging.
Packaging:
Composant A: 15 Kg / pallet 36 drums
Composant B: 5 Kg / palet 36 boxes with 4 drums = 144 units
Composant A: 3 Kg / pallet 9 boxes with 4 drums = 36 units
Composant B: 1 Kg / pallet 12 boxes with 12 drums= 144 units
· Manufactured according to ISO 9001 quality management and ISO 14001 for environmental management.

Related Products

 

DATA PROTECTION

 

In cases where the user must provide data of a personal nature to TEXSA SYSTEMS SLU to use any of the Web services, the former will be expressly informed each time of the existence of an automated data base, the aim of same, those receiving the information and identity and address of the person responsible for data treatment, all with the aim of complying with that stipulated in Organic Law 15/1999 of 13th December, for the Protection of Data of a Personal Nature. To this effect, TEXSA SYSTEMS SLU shall reserve confidentiality of the data obtained and the users can exercise all rights to access, amendment, cancellation and any others referred to in aforementioned Organic Law 15/1999.

TEXSA SYSTEMS SLU has adopted all the necessary measures of a technical and organisational nature, to guarantee the security of the data of a personal nature, with the aim of preventing their alteration, loss, treatment or unauthorised access, in accordance with the requirements and conditions called for by Royal Decree 994/1999 of 11th June, in which the Regulation of safety measures of automated files containing data of a personal nature, is passed, notwithstanding the user's acceptance and knowledge that to date totally impregnable safety measures do not exist.

In case of doubt or the need to extend the information covering any of the above items, please do not hesitate to contact TEXSA SYSTEMS SLU.

 

TEXSA SYSTEMS SLU.
C/Ferro Nº7,
Polígono Industrial Can Pelegrí,
Castellbisbal
08755, Barcelona - Spain
NIF B66067687

Tel. (+34) 93 635 14 00
Fax (+34) 93 635 14 80

Email:  lopd@texsa.com